It also allows you to transfer external calls from one handset to another, and set up a 3-way conference with two handsets and an external call. If you try to make a call while another handset is already on an external call, you will hear a busy tone for a few seconds before the display returns to standby. In standby mode, press I. Press Ton a called handset to answer the internal call, where both internal callers can talk. To end the intercom call, press Oon either handset. During the call, press Ito put the external call on hold.
Note:Note:Note:Note: If there is no answer from the called handset, or you wish to cancel the intercom call before it is answered, press Ito return to the external call. Press Ton the called handset to answer the internal call, where both internal callers can talk.
When the intercom call is connected, you can choose from the following options on the originating handset: 1 Press and hold Ifor 2 seconds to connect both handsets to the call in conference mode. Press Oon the originating handset to transfer the external call to the called handset. A long press on the keys in standby mode will automatically dial the stored phone number. From the home screen, press M. Otherwise, the stored name is displayed. Press Mto enter the menu options. Enter the name of the contact and press M.
If you make a mistake, press mto delete the last character entered. Otherwise the stored number is displayed. Enter the number of your contact and press M. If you make a mistake, press mto delete the last digit entered. Press Oto return to standby mode. Press Magain to confirm. Each phonebook entry can have a maximum of 24 digits for the phone number and 12 characters for the name. Enter the name of the contact maximum 12 characters using the keypad.
Press Mto confirm the name entry. Enter the number of the contact maximum 24 digits using the keypad. Press Mto confirm. Note:Note:Note:Note: You cannot store a new phonebook entry when the memory is full. In this case, you have to delete existing entries to make space for new ones. From the home screen, press - to open the phonebook list. Press Mto view the details of the selected entry.
For example, pressing 2will show the first entry starting with A. Pressing 2again will show the first entry starting with B, and so on Edit the name using the keypad.
Press mto delete characters. Edit the number and then press Mto confirm. Note:Note:Note:Note: If the call is from someone whose number is unavailable e. If the call is from someone whose number is withheld e. Information about incoming calls varies by country and network operators. Only the most recent call is saved if there are repeat calls from the same number.
Enter the name of the contact maximum 12 characters and then press Mto save. Press M. A maximum of 24 digits can be displayed for each entry. From the home screen, press R. Edit the number and press Mto confirm. You can also set the date and time manually. Enter the current date and press Mto confirm. Enter the current time and press Mto confirm. For hour format, enter pm as [1], [3], [3], [0]. When an alarm is set, the alarm icon is shown on the handset display. When the alarm time is reached, the handset will sound an alarm for 1 minute, at the same volume setting as the handset ringer.
If the ringer is off, it will ring at volume setting 1. When the alarm rings, you can press any key on the handset to stop the ringing, even if the keylock is activated. Press Mto select the option. Press Mto confirm the alarm setting. The ringer off icon displays on the screen when ringer off feature is activated. You can choose to turn this tone on or off. Press mto delete the letters one by one and enter the new name maximum 10 characters.
Note:Note:Note:Note: Once the display language is set, the handset will switch to display in the selected language immediately. Handset registration is only necessary when you buy extra handsets or if a handset has become faulty.
Note:Note:Note:Note: Each handset can only be registered to one base. You need to enter the Master PIN before you can register or unregister handsets. The default Master PIN is Press and hold the key under the base unit for approximately 5 seconds.
On the handset, press M. If this happens, repeat from step 1. You will need to repeat from step 1 above. The default Master PIN number is The maximum length of the Master PIN is 8 digits. Enter the new PIN and then press Mto confirm. You should normally leave the Recall Time at its default setting, Short ms Short ms Short ms Short ms , as this is the standard recall required in the telephone network.
However, it can be changed to Medium ms or Long ms if your telephone is connected to a PBX that requires a different recall time. Note:Note:Note:Note: Upon reset, all your personal settings, call log and redial list entries will be deleted and the phone will return to its default settings. However, your phonebook will remain unchanged after reset. All connectors are securely inserted into their sockets. Mains power for the base unit is switched on at the socket.
Press and hold Oto switch it back on. The base unit needs mains power for normal operation of the phone — not just for charging the batteries.
Make sure that you are using the telephone line cable supplied with your phone. Other telephone line cables might not work.
Move the handset closer to the base unit. Check the Battery Level symbol on the display. If it is low, put the handset back on the base unit or charging pod to recharge the batteries. Switch off the power at the mains socket, wait for a short while and then switch it back on. This may solve the problem. Only one handset or the base unit can be connected to an external line at a time.
If the handset display shows , the base is already being used by another handset. Make sure that you are using the telephone line cable that was supplied with your phone. Make sure that the ringer volume settings are not set to off.
Increase the ringer volume settings. Try moving the base unit away from other electrical equipment, such as a television or a computer. For example, in a two-floor building, the first-floor landing is an ideal place. Move closer or your call may be cut off. The caller may have withheld their number by dialling You must delete existing entries to make space for new ones.
Make sure that you have entered the correct number for the other handset. You may need to replace the batteries. Check the connection between the base unit and the mains power socket. Dispose of used batteries safely — do not burn, immerse them in water, disassemble, or puncture the batteries.
Do not use non-rechargeable batteries in your handset — they may explode, causing damage. You will need to unregister a handset in order to register a new one. If the fault persists Disconnect all other instruments connected to the same line and try to make a call.
Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket. Try making a call. If this works, the line is OK. If the call does not work, and you are using a two-way socket adapter, remove it and plug a telephone directly into the socket. If the call now works, the adapter may be faulty. If you cannot make a call, the fault may be on the exchange line. Contact the service provider.
This equipment and all its components, subsystems and consumable materials form an integral part of this product and when you decide to dispose of them you have to take them to a local recycling centre for appropriate waste disposal, in compliance with the current regulations.
Details about the location of these centres can be obtained from your local authority. Please be aware of the local rules on separate collection of batteries. The correct disposal of batteries helps protect the environment and prevent health hazards.
This guarantee does not cover any faults or defects caused by accidents, misuse, fair wear and tear, neglect, faults on the telephone line, lightning, tampering with the equipment, or any attempt at adjustment or repair other than through approved agents. Please keep your sales till receipt this is your guarantee.
You should also keep the original packaging material. In the unlikely event that you need to return your phone system to our Repair Centre while it is under guarantee, there may be a handling charge. Disconnect the base unit from the telephone line and the mains electricity supply. Pack up all parts of your phone system, using the original package.
Return the unit to the shop where you bought it, making sure you take your sales receipt. Remember to include the mains adapter. Call Helpline on for UK only and ask for a quotation of the repair charge and details of where to send your phone system for repair.
Make sure you include with your phone system. Your name and address A cheque or postal order for the value of the repair A brief description of the fault. Return your phone system to the address given by the Service Department.
In menu mode, press to scroll down. Page 16 Displays when the handset is registered and within range of the base station. Flashes when the handset is out of range and is searching for a base. Displays when the handset is in speaker mode. Turns on when confirmation of selection or programming is available. Page Call From The Phonebook 4.
Press to select the desired entry in the phonebook and then press to dial out the selected phonebook number. If there is no answer from the called handset within one minute, the paging will be cancelled automatically. If no handset is registered to the base, 4 beeps will be heard and it will return to standby mode. A long press on the keys in standby mode will automatically dial the stored phone number. Each phonebook entry can have a maximum of 24 digits for the phone number and 12 characters for the name.
A maximum of 24 digits can be displayed for each entry. Page Delete A Redial Number 7. Page Change The Time Format 8. When an alarm is set, the alarm icon is shown on the handset display. When the alarm time is reached, the handset will sound an alarm for 1 minute, at the same volume setting as the handset ringer.
Page Set The Alarm Tone 8. Set the Set the Set the You can choose to turn this tone on or off. Handset registration is only necessary when you buy extra handsets or if a handset has become faulty. Page Un-Register Your Handset Page Change The Recall Time All connectors are securely inserted into their sockets. The base unit needs mains power for normal operation of the phone — not just for charging the batteries. Make sure that you have entered the correct number for the other handset.
This guarantee does not cover any faults or defects caused by accidents, misuse, fair wear and tear, neglect, faults on the telephone line, lightning, tampering with the equipment, or any attempt at adjustment or repair other than through approved Print page 1 Print document 50 pages.
0コメント